IS26KL256S-DABLE00

容量 256Mb
電壓 2.7V-3.6V
類型 HyperFlash™
狀態 Prod
評注
频率 100 Mhz
溫度範圍 -40 to 125 deg °C
腳位類型 24-Ball BGA (6x8mm)
ROHS版 L = true
外包裝 = TRAY
溫度範圍 E = Extended (-40°C to +105°C)
Model Number 00 = FBGA 24-ball, 1.0mm height
電壓 - 電源 KL = 3.0V
密度配置 256 = 256M
包裝代碼 B = BGA 6x8mm, 1.0mm pitch (24 VF-BGA)
產品系列 26 = HyperFlash
Device Technology S = 65nm, MirrorBit Process technology
速度等級 DA = 100MHz

IS26KL256S-DABLE00 特徵

  • 3.0V I/O, 11 bus signals
    • Single ended clock
  • 1.8V I/O, 12 bus signals
    • Differential clock (CK, CK#)
  • Chip Select (CS#)
  • 8-bit data bus (DQ[7:0])
  • Read-Write Data Strobe (RWDS)
    • HyperFlash™ memories use RWDS only as a Read Data Strobe
  • Up to 333 MB/s sustained read throughput
  • Double-Data Rate (DDR)
    • two data transfers per clock
  • 166-MHz clock rate (333 MB/s) at 1.8V VCC
  • 100-MHz clock rate (200 MB/s) at 3.0V VCC
  • 96-ns initial random read access time
    • Initial random access read latency: 5 to 16 clock cycles
  • Sequential burst transactions
  • Configurable Burst Characteristics
    • Wrapped burst lengths:
    • 16 bytes (8 clocks)
    • 32 bytes (16 clocks)
    • 64 bytes (32 clocks)
    • Linear burst
    • Hybrid option — one wrapped burst followed by linear burst
    • Wrapped or linear burst type selected in each transaction
    • Configurable output drive strength
  • Low Power Modes
    • Active Clock Stop During Read: 12 mA, no wake-up required
    • Standby: 25 µA (typical), no wake-up required
    • Deep Power-Down: 8 µA (typical)
    • 300 µs wake-up required
  • INT# output to generate external interrupt
    • Busy to Ready Transition
    • ECC detection
  • RSTO# output to generate system level power-on reset
    • User configurable RSTO# Low period
  • 512-byte Program Buffer
  • Sector Erase
    • Uniform 256-kB sectors
    • Optional Eight 4-kB Parameter Sectors (32 kB total)
  • Advanced Sector Protection
    • Volatile and non-volatile protection methods for each sector
  • Separate 1024-byte one-time program array
  • Operating Temperature
    • Industrial (
    • 40°C to +85°C)
    • Extended (
    • 40°C to +105°C)
    • Extended + (
    • 40°C to +125°C)
    • Automotive, AEC-Q100 Grade A1 (
    • 40°C to +85°C)
    • Automotive, AEC-Q100 Grade A2 (
    • 40°C to +105°C)
    • Automotive, AEC-Q100 Grade A3 (
    • 40°C to +125°C)
  • ISO/TS16949 and AEC Q100 Certified
  • Endurance
    • 100,000 program/erase cycles
  • Retention
    • 20 year data retention
  • Erase and Program Current
    • Max Peak  100 mA
  • Packaging Options
    • 24-Ball FBGA

概觀

The ISSI HyperFlash family of products are high-speed CMOS, MirrorBitNOR flash devices with the HyperBus low signal count DDR (Double Data Rate) interface, that achieves high speed read throughput. The DDR protocol transfers two data bytes per clock cycle on the data (DQ) signals. A read or write access for the HyperFlash consists of a series of 16-bit wide, one clock cycle data transfers at the internal HyperFlash core and two corresponding 8-bit wide, one-half-clock-cycle data transfers on the DQ signals. Both data and command/address information are transferred in DDR fashion over the 8-bit data bus. The clock input signals are used for signal capture by the HyperFlash device when receiving command/address/data information on the DQ signals. The Read Data Strobe (RWDS) is an output from the HyperFlash device that indicates when data is being transferred from the memory to the host. RWDS is referenced to the rising and falling edges of CK during the data transfer portion of read operations. Command/address/write-data values are center aligned with the clock edges and read-data values are edge aligned with the transitions of RWDS. Read and write operations to the HyperFlash device are burst oriented. Read transactions can be specified to use either a wrapped or linear burst. During wrapped operation, accesses start at a selected location and continue for a configured number of locations in a group wrap sequence. During linear operation accesses start at a selected location and continue in a sequential manner until the read operation is terminated, when CS# returns High. Write transactions transfer one or more16-bit values.

 

相關IC编號

IC 編號 庫存數量 可用數量 IC 編號 庫存數量 可用數量
IS26KL256S-DABLE00-TR IS26KL256S-DABLA303
IS26KL256S IS26KL256S-DABLA303-TR
IS26KL256S-DABLA100 IS26KL256S-DABLE03
IS26KL256S-DABLA100-TR IS26KL256S-DABLE03-TR
IS26KL256S-DABLA103 IS26KL256S-DABLE100
IS26KL256S-DABLA103-TR IS26KL256S-DABLE100-TR
IS26KL256S-DABLA200 IS26KL256S-DABLE103
IS26KL256S-DABLA200-TR IS26KL256S-DABLE103-TR
IS26KL256S-DABLA203 IS26KL256S-DABLI00 10,000
IS26KL256S-DABLA203-TR IS26KL256S-DABLI00-TR
IS26KL256S-DABLA300 IS26KL256S-DABLI03
IS26KL256S-DABLA300-TR IS26KL256S-DABLI03-TR