IS25WP128-JKLE-TR

Density 128M
Vcc 1.65-1.95V
Type Multi I/O SPI, QPI, DTR
Status Prod
Frequency 50M/133Mhz
Temp Range -40 to 125°C
Package Type SOIC, WSON, TFBGA
Alt Version Doc
Special Options J = Standard
Operating Voltage Range W = 1.65-1.95V
Rev Control blank = First Rev
Package Type K = 8 pin WSON (6x5 mm)
Product Family P = Single/Dual/Quad/QPI SPI DTR Options Available
Temperature Grade E = Extended grade (-40°C to +105°C)
Lead Free Package L = Lead-Free (Pb Free) and Halogen Free
Density 128 = 128M
Outpack Tape on Reel

IS25WP128-JKLE-TR Features

  • Industry Standard Serial Interface
  • - IS25WP128: 128Mbit/16Mbyte - 256 bytes per Programmable Page - Supports standard SPI, Fast, Dual, Dual I/O, Quad, Quad I/O, SPI DTR, Dual I/O DTR, Quad I/O DTR, and QPI - Supports Serial Flash Discoverable Parameters (SFDP)
  • High Performance Serial Flash (SPI)
  • - 50MHz Normal and 133Mhz Fast Read - 532 MHz equivalent QPI - DTR (Dual Transfer Rate) up to 66MHz - Selectable Dummy Cycles - Configurable Drive Strength - Supports SPI Modes 0 and 3 - More than 100,000 Erase/Program Cycles - More than 20-year Data Retention
  • Flexible & Efficient Memory Architecture
  • - Chip Erase with Uniform: Sector/Block Erase (4/32/64 Kbyte) - Program 1 to 256 Bytes per Page - Program/Erase Suspend & Resume
  • Efficient Read and Program modes
  • - Low Instruction Overhead Operations - Continuous Read 8/16/32/64-Byte Burst Wrap - Selectable Burst Length - QPI for Reduced Instruction Overhead - AutoBoot Operation
  • Low Power with Wide Temp. Ranges
  • - Single 1.65V to 1.95V Voltage Supply - 10 mA Active Read Current - 8 µA Standby Current - 1 µA Deep Power Down - Temp Grades: Extended: -40°C to +105°C Auto Grade (A3): -40°C to +125°C
  • Advanced Security Protection
  • - Software and Hardware Write Protection - Power Supply Lock Protection - 4x256-Byte Dedicated Security Area with OTP User-lockable Bits - 128 bit Unique ID for Each Device (Call Factory)

Overview

The IS25WP128 Serial Flash memory offers a versatile storage solution with high flexibility and performance in a simplified pin count package. ISSI’s “Industry Standard Serial Interface” Flash is for systems that require limited space, a low pin count, and low power consumption. The device is accessed through a 4-wire SPI Interface consisting of a Serial Data Input (SI), Serial Data Output (SO), Serial Clock (SCK), and Chip Enable (CE#) pins, which can also be configured to serve as multi-I/O (see pin descriptions). The device supports Dual and Quad I/O as well as standard, Dual Output, and Quad Output SPI. Clock frequencies of up to 133MHz allow for equivalent clock rates of up to 532MHz (133MHz x 4) which equates to 66Mbytes/s of data throughput. The IS25xP series of Flash adds support for DTR (Double Transfer Rate) commands that transfer addresses and read data on both edges of the clock. These transfer rates can outperform 16-bit Parallel Flash memories allowing for efficient memory access to support XIP (execute in place) operation. The memory array is organized into programmable pages of 256-bytes. This family supports page program mode where 1 to 256 bytes of data are programmed in a single command. QPI (Quad Peripheral Interface) supports 2- cycle instruction further reducing instruction times. Pages can be erased in groups of 4Kbyte sectors, 32Kbyte blocks, 64Kbyte blocks, and/or the entire chip. The uniform sector and block architecture allows for a high degree of flexibility so that the device can be utilized for a broad variety of applications requiring solid data retention. GLOSSARY Standard SPI In this operation, a 4-wire SPI Interface is utilized, consisting of Serial Data Input (SI), Serial Data Output (SO), Serial Clock (SCK), and Chip Enable (CE#) pins. Instructions are sent via the SI pin to encode instructions, addresses, or input data to the device on the rising edge of SCK. The SO pin is used to read data or to check the status of the device. This device supports SPI bus operation modes (0,0) and (1,1). Mutil I/O SPI Multi-I/O operation utilizes an enhanced SPI protocol to allow the device to function with Dual Output, Dual Input and Output, Quad Output, and Quad Input and Output capability. Executing these instructions through SPI mode will achieve double or quadruple the transfer bandwidth for READ and PROGRAM operations. QPI The device supports Quad Peripheral Interface (QPI) operations only when the device is switched from Standard/Dual/Quad SPI mode to QPI mode using the enter QPI (35h) instruction. The typical SPI protocol requires that the byte-long instruction code being shifted into the device only via SI pin in eight serial clocks. The QPI mode utilizes all four I/O pins to input the instruction code thus requiring only two serial clocks. This can significantly reduce the SPI instruction overhead and improve system performance. Only QPI mode or SPI/Dual/Quad mode can be active at any given time. Enter QPI (35h) and Exit QPI (F5h) instructions are used to switch between these two modes, regardless of the non-volatile Quad Enable (QE) bit status in the Status Register. Power Reset or Hardware/Software Reset will return the device into the standard SPI mode. SI and SO pins become bidirectional I/O0 and I/O1, and WP# and HOLD# pins become I/O2 and I/O3 respectively during QPI mode. DTR In addition to SPI and QPI features, the device also supports Fast READ DTR operation. DTR operation allows high data throughput while running at lower clock frequencies. Fast READ DTR operation uses both rising and falling edges of the clock for address inputs, and data outputs, resulting in reducing input and output cycles by half.

 

Related Part Number(s)

Description Stock Qty Available Qty Description Stock Qty Available Qty
IS25WP128-JKLE 10,000 IS25WP128-QBLA3
IS25WP128-JBLA3 10,000 IS25WP128-QBLA3-TR
IS25WP128-JBLA3-TR IS25WP128-QBLE
IS25WP128-JBLE 10,000 IS25WP128-QBLE-TR
IS25WP128-JBLE-TR IS25WP128-QGLA3
IS25WP128-JGLA3 10,000 IS25WP128-QGLA3-TR
IS25WP128-JGLA3-TR IS25WP128-QGLE
IS25WP128-JGLE 10,000 IS25WP128-QGLE-TR
IS25WP128-JGLE-TR IS25WP128-QHLA3
IS25WP128-JHLA3 10,000 IS25WP128-QHLA3-TR
IS25WP128-JHLA3-TR IS25WP128-QHLE
IS25WP128-JHLE 10,000 IS25WP128-QHLE-TR
IS25WP128-JHLE-TR IS25WP128-QKLA3
IS25WP128-JKLA3 10,000 IS25WP128-QKLA3-TR
IS25WP128-JKLA3-TR IS25WP128-QKLE
IS25WP128-JLLA3 10,000 IS25WP128-QKLE-TR
IS25WP128-JLLA3-TR IS25WP128-QLLA3
IS25WP128-JLLE 10,000 IS25WP128-QLLA3-TR
IS25WP128-JLLE-TR IS25WP128-QLLE
IS25WP128-JMLA3 10,000 IS25WP128-QLLE-TR
IS25WP128-JMLA3-TR IS25WP128-QMLA3
IS25WP128-JMLE 10,000 IS25WP128-QMLA3-TR
IS25WP128-JMLE-TR IS25WP128-QMLE
IS25WP128-PHLE IS25WP128-QMLE-TR
IS25WP128-PHLE-TR IS25WP128-RGLA3 10,000
Show All (63)